How To Clean Zebra Zxp Series 3

1. The LCD of my control panel shows "Command Error".
2. The printer won't have my cards.
3. My cards get stuck in the printer. What do I do?
4. My ribbon keeps breaking.
5. How practise I clean the printer?
6. How practise I clean the printhead?

The LCD of my control panel shows "Control Mistake".

These messages usually appear when cards volition not print and you cannot reset printer.
To prepare the problem, follow these steps:

1. Disconnect the interface cable from the printer.
2. Become to the printer queue and abolish all jobs for that printer. Await for all jobs to be deleted.
3. Turn printer power off, wait 5 seconds, and plow back on.

You should now have a "Prepare" message or a solid green low-cal indicating the printer status is normal and it is ready for the next print job.

The printer won't take my cards.

The Printer is unable to feed a card from the card hopper.

• Verify the carte thickness setting is ready to the thickness of your cards.
• Verify the Cleaning roller is properly installed on the Ribbon Cartridge.
• Bank check for card slippage. If necessary, run the Printer cleaning routine.
• Verify that your cards are within the accepted carte du jour size range.
• Verify the cards are not sticking together.

My cards get stuck in the printer. What practise I practice?

Clear the jam and try the following options:

• Run a cleaning cycle.
• Try dissimilar cards.
• Manually clean the rollers.
• Update the printer commuter and firmware to the latest on Zebra'southward website.

My ribbon keeps breaking.

Try the following options:

• Endeavor a different ribbon.
• Calibrate the ribbon sensor.
• Update the printer driver and firmware to the latest on Zebra's website.
• Try different cards.
• Verify that you are using the correct power supply.
• Manually make clean the rollers.
• Lower the dye sub intensity in the print driver.

Notation that you can nevertheless employ a ribbon that broke by taping it back on to the take- upward core.

How exercise I make clean the printer?

1. Place the printer ability switch in the ON position, and so press and hold the Multi-Function Control Push for 5 seconds.
2. When the cleaning bicycle is initiated, the LCD message REMOVE RIBBON So Close Chapeau will display.
3. Subsequently the ribbon is removed and the lid is airtight, the message EMPTY FEEDER Then CLOSE COVER will display.
4. If the lid is opened and airtight without removing the ribbon, the REMOVE RIBBON Then Shut LID message volition remain.
5. One time the ribbon is removed and the encompass is closed, the firmware will eject any carte inside the printer. The message EJECTING Carte du jour volition display.
6. The LCD will display FEED LONG CLEANING CARD. When the presence of the cleaning bill of fare is sensed, the rollers will accept the card into the printer.
7. When the cleaning process is done, the printer will eject the cleaning bill of fare. If the carte du jour sensor still senses the cleaning carte du jour, the message REMOVE LONG CLEANING CARD will display.
8. Once the long cleaning carte is no longer sensed past the card go out sensor, the message INSERT FEEDER CLEANING CARD will brandish. Open the feeder cover, and insert the feeder cleaning card.
9. When the feeder cleaning card has been sensed by the feeder card sensor, the message CLOSE FEEDER Embrace volition display.
10. When feeder cleaning is consummate, the message REMOVE FEEDER CLEANING CARD will display.
11. After the menu is removed, the LCD will display READY. You may now reload the ribbon and cards and continue press.

How do I clean the printhead?

1. Place the printer power switch in the OFF (O) position.
2. Open the printer chapeau by pressing the cover release button, and open up the cover fully to reveal the Printhead mounted on the inside of the cover.
3. Make clean the Printhead past moving an alcohol-moistened swab tip side-to-side across the Printhead elements. But use moderate strength.
4. Allow ii to three minutes for the printhead to dry before placing the printer power switch in the ON position.

Source: https://www.idsecurityonline.com/zxp-series-3-troubleshooting.htm

Posted by: robinsondointow.blogspot.com

Share this post